RG
OPEN_TO_WORK: HW_ENGINEER

Design. Route. Deploy._

From schematic to hardware.

Embedded Hardware Design Engineer with hands-on experience across schematic capture, multilayer PCB layout, power electronics, and firmware bring-up. Deepest project work has been in UAV flight controllers and power systems, with practical exposure to KiCad, Altium, and LTspice.

↓  Scroll to explore

Building Hardware with Precision

A hardware design journey shaped by hands-on schematic capture, PCB layout, and power electronics work.

I am an Embedded Hardware Design Engineer focused on the journey from schematic to prototype β€” combining multilayer PCB layout, power electronics, and firmware bring-up. I enjoy breaking complex hardware problems into clean, testable subsystems and using simulation-driven design to push boards toward reliable field operation.

βš™ PCB Layout β—ˆ Power Electronics βœ“ Firmware Bring-Up ⌘ EMI-Aware Design
6-Layer
Max PCB Complexity Designed
7
Projects Completed
2.4kW
Max Power Delivered
hw_profile.py Python
# /home/raju/hw_profile.py
domain = "Embedded Hardware Design"
strengths = {
"PCB Layout",
"Power Electronics",
"Firmware Bring-Up",
"EMI-Aware Design"
}
mindset = "Every trace has a reason"
print("Design. Route. Deploy.")

Tools & Competencies

A hardware-engineering toolkit spanning PCB design, power electronics, and embedded firmware.

πŸ”§

PCB Design & Layout

Schematic Capture Multilayer Layout Component Placement Impedance Control DFM Review Gerber Generation BOM Management EMI/EMC-Aware Routing
⚑

Power Electronics

Buck Converters UVLO Soft-Start EMI Filtering Thermal Design Reverse-Polarity Protection Parallel Load Sharing High-Voltage Design
πŸ’»

Firmware & Embedded

C Embedded C Bare-Metal Drivers STM32CubeIDE Keil Β΅Vision Register-Level Programming
πŸ“‘

Communication Protocols

SPI I2C UART CAN USB Wi-Fi
πŸ“

Microcontrollers & Platforms

STM32 (F1/F4) ESP32 Arduino UNO 8051 PIC Raspberry Pi
πŸ”¬

Simulation & Verification

LTspice PSpice NI Multisim Proteus Bench Validation Thermal Testing

πŸ› οΈ Design Tool Suite

KiCad
Open Source
Altium Designer
Altium
EasyEDA
JLCPCB
LTspice
Analog Devices
PSpice
Cadence
STM32CubeIDE
STMicroelectronics
Proteus
Labcenter

Hands-On Projects

Hands-on projects demonstrating end-to-end hardware design, from schematic through bench validation.

πŸ›©οΈ
KiCad STM32F427 6-Layer PCB ArduPilot

UAV Flight Controller β€” Ti-Circle v1

Designed a custom flight controller from scratch supporting ArduPilot firmware, routed on a 6-layer PCB with 250+ components centered around the STM32F427. Integrated a dedicated I/O co-processor and multi-rail power supply for flight-critical peripherals.

🧬 6-Layer PCB πŸ”² 250+ Components πŸ“‘ SPI/I2C/UART
πŸ”Œ
EasyEDA LTspice PSpice High-Voltage

Tethered Drone Power System

Engineered end-to-end power delivery for a tethered drone platform: an AC-DC base station converting 230V AC to 360V DC @ 8A, and an isolated air-unit converter stepping that down to 24V DC @ 100A. Added real-time telemetry and automatic failover arbitration.

⚑ 2.4kW πŸ”‹ 360V DC Link πŸ” Auto Failover
πŸ”‹
KiCad LTspice LT8645SHV-2

5V Power Module for UAV Avionics

Designed a high-efficiency, wide-input 5V DC-DC power module supporting 3S–12S LiPo input using the LT8645SHV-2 synchronous buck converter, with reverse-polarity protection, UVLO, soft-start, and a low-EMI, low-ripple PCB layout.

πŸ”‹ 3S–12S LiPo πŸ“‰ Low-EMI Layout πŸ›‘οΈ UVLO + Soft-Start
🧩
KiCad PCB Design EMI/EMC Cube Orange+

Custom Carrier Board for Cube Orange+

Designed a custom Cube Orange+ carrier board with board-to-board connectivity for full UAV peripheral integration. Implemented EMI/EMC-aware layout, controlled-impedance routing, ground-plane management, and high-current signal isolation; completed schematic, PCB, DFM, and Gerber release followed by bench and flight validation.

🧩 Board-to-Board πŸ“ Controlled Impedance ✈️ Flight Tested
πŸ”„
KiCad LTspice LM2596S-ADJ

Adjustable DC-DC Step-Down Converter

Designed a wide-input adjustable buck converter using the LM2596S-ADJ, accepting 5–40V input and delivering an adjustable 3.3–15V output via a feedback potentiometer, rated for up to 3A continuous load.

πŸ”Œ 5–40V In 🎚️ 3.3–15V Out ⚑ 3A

Professional Experience

Hands-on hardware R&D across UAV avionics, power electronics, and fault-tolerant flight systems.

May 2025 – Apr 2026

Research & Development Intern

TiHAN-IIT Hyderabad, Telangana
  • Designed a custom UAV flight controller on a 6-layer PCB with 250+ components, supporting ArduPilot firmware around the STM32F427
  • Developed a high-efficiency 5V wide-input power module (LT8645SHV-2) for 3S–12S LiPo systems, with UVLO, soft-start, and low-EMI layout
  • Built a custom carrier board for the Cube Orange+ flight controller with EMI/EMC-aware layout β€” flight-tested on a drone platform
  • Engineered a 2.4kW tethered drone power system (230V AC β†’ 360V DC β†’ 24V DC @ 100A) with real-time telemetry and automatic failover
May 2026 – Present

Junior Research Assistant Fellow (JRAF)

TiHAN-IIT Hyderabad, Telangana
  • Developing a redundant-feature UAV flight controller architecture with hardware-level fault tolerance, designed to maintain flight-critical functions during single-point subsystem failures
  • Designing UAV power modules with wide-input voltage capability, high conversion efficiency, and low-EMI power-stage/layout practices for stable and clean delivery to flight-critical avionics
  • Driving hardware development from schematic capture and component-level design through multilayer PCB layout, DFM review, prototype bring-up, and bench validation
  • Applying reliability-focused hardware design practices across flight-control and power subsystems to improve system robustness and operational continuity in UAV platforms

Academic Background

Academic qualifications.

πŸŽ“
B.Tech
Electronics and Communication Engineering
Dec 2021 – May 2025
Rajiv Gandhi University of Knowledge Technologies - Nuzvid
Percentage: 80%
πŸ“˜
Class XII
Pre University Course
Sep 2019 – Nov 2021
Rajiv Gandhi University of Knowledge Technologies - Nuzvid
Percentage: 88%
πŸ“š
Class X
Z.P.P High School - Aratlakatta
Jun 2018 – Apr 2019
Percentage: 100%

Certifications

NPTEL / SWAYAM certifications completed in electronics and embedded systems.

πŸ…
Introduction to Industry 4.0 and Industrial IoT
NPTEL (Elite + Silver)
Apr 2025
πŸ…
ESD: Hands-On Circuits and PCB Design with CAD Software
NPTEL (Elite + Silver)
Oct 2024
πŸ…
VLSI Design Flow: RTL to GDS
NPTEL (Elite + Silver)
Oct 2024
πŸ“œ
Introduction to Embedded Systems
NPTEL
Apr 2024
πŸ“œ
Embedded for Beginners
NIELIT, NIT Calicut
Jan 2024

Let's Connect

Open to Embedded Hardware Design Engineer roles, freelance PCB/embedded projects, and collaborations.

Get in Touch

I'm actively seeking opportunities in embedded hardware design, PCB layout, and power electronics engineering. Whether you're hiring, have a project, or just want to talk hardware β€” I'd love to hear from you.

RG
Senior
Local assistant
Hi! I can answer questions about my projects, skills, education, certifications, and career interests.